• WELCOME TO ZCCCT!Contact us:export@zccct.com
    Home Technical Development Solution
    Technical Development

    ZCCCT tools Application in Blowers Casing

    Date:2020/04/13




    The chassis of blowers casing is for Tri-lobe Roots Blowers, which is mentioned in the cases below. Its most important feature is the little change of low volume while the pressure is adjusted in a permitted range during the application process. In addition, there is a wide selection of operating point for pressure. What's more, it has no process of internal compression and the transmission of air is mandatory. Also, oil is not contained in the transmitting agents. The consistency of dynamic balance for rotor is high, and the overall vibration is low. Therefore, it operated with safety and reliability in a long term. Also, it is very convenient to maintain due to its compact structure. It possesses more advanced structure and higher machining efficiency with improved design. The function of Blower is to transmit the clean air, and it transmits the semi-water gas, water gas, sulfur dioxide, and other neutral gas under purification process as well. However,inflammable, explosive, toxic and highly corrosive agents are not permitted to transmit. It is widely applicable in economic sectors covering metallurgy,light industry, textile, coal, mechanical industry, electric power industry,petroleum, cement industry, chemical engineering industry, construction materials, environmental protection, paper making, sewage disposal, aquaculture industry, and pneumatic conveying.


    Crafts:

    ◆Rough Milling for Equipping Face of Chassis Pedestal and Flange Face of inlet Hole


    ◆Finish Milling for Equipping Face of Chassis Pedestal and Flange Face of inlet Hole


    ◆Rough Milling for Rake Face and Flank Face of Rotor cavity


    ◆Finish Milling for Rake Face and Flank Face of Rotor cavity


    ◆Rough Milling for Flange Face of vent Hole


    ◆Finish Milling for Flange Face of vent Hole


    ◆Rough Boring of Rotor Cavity Hole


    ◆Finish Boring of Rotor Cavity Hole


    ◆Thread Hole Drilling for Rake Face and Flank Face of Rotor Cavity


    ◆Locating Hole Drilling for Rake Face and Flank Face of Rotor Cavity


    ◆Bolt Hole Drilling on Pedestal


    ◆Thread Hole Drilling for Flange Face of  Vent Hole and Inlet Hole


    ◆Hole Chamfering for Thread Holes and Bolt Holes on Each Faces


    ◆Thread Hole-making for Rake Face and Flank Face of Rotor Cavity


    ◆Thread Hole Tapping for Flange Face of vent hole and inlet hole


    Rough Milling for Equipping Face of Chassis Pedestal and Flange Face of inlet Hole

    Rough Milling for Rake Face and Flank Face of Rotor Cavity

    FMD02 Series of Face Milling Tools

    Rough Milling for Flange Face of vent Hole

    FMD 02Series of Face Milling Tools



    Tool: FMD02-100-B32-PN11-10

    Insert: YBD252/PNEG110512R-CR

    Cutting data: V=180m/min   f=0.3mm/z  ap=3mm

    Finish Milling for Equipping Face of Chassis Pedestal and Flange Face of inlet Hole

    Finish Milling for Rake Face and Flank Face of Rotor Cavity

    FMP02 Series of Face Milling Tools

    Finish Milling for Flange Face of vent Hole -

    FMP02 Series of Face Milling Tools

    Tool: FMP02-100-B32-SE09-08

    Insert: YBG202/SEET09T308PER-PF

    Cutting data: V=200m/min   f=0.1mm/z  ap=1mm

    Rough Boring of Rotor Cavity Hole

    Tool: FMP02-100-B32-SE09-08

    Insert: YBG202/SEET09T308PER-PF

    Cutting data: V=200m/min   f=0.1mm/z  ap=1mm

    Finish Boring of Rotor Cavity Hole----large diameter boring cutter

    Tool: LD60-D380-400455-40L(cutter head)

    LR170-CN12(seat)

    Insert: YBD152/CCMG120408-PM

    Cutting data: V=150m/min   f=0.12mm/z  ap=5mm

    Finish Boring of Rotor Cavity Hole ---large diameter boring cutter


    Tool: LD60-D380-400455-40L(cutter head)

              F114-67153-CC06(Chuck)

              FB90-LD-65*75(Seat)

              LCW94-65*72(Balancing Weight)

    Tool: YNG151C/CCGT060204-SF

    Cutting data: V=180m/min   f=0.05mm/z  ap=0.3mm

    Thread Hole Drilling For Rake Face and Flank Face of Rotor Cavity

    Tool: 1576PC05-1750

    Cutting data: n=1800r/min   f=0.25mm/r


    Locating Hole Drilling for Rake Face and Flank Face of Rotor Cavity

    Tool: 1576PC05-1750

    Cutting data: n=1600r/min   f=0.28mm/r


    Bolt Hole Drilling on Pedestal

    Tool: ZTD02-280-XP32-SP09-02

    Insert: YBG205/SPGT090408-PM(External edge)

                YBG212/SPGT090408-PM(Internal edge)

    Cutting data: n=1600r/min   f=0.28mm/r 


    Thread Hole Drilling forFlange Face of vent hole and inlet hole

    Tool: 1576PC05-1400

    Cutting data: n=2100r/min   f=0.22mm/r


    Hole Chamfering for ThreadHoles and Bolt Holes on Each Faces

    Tool: 1143SC90-2000

    Cutting data: n=1600r/min   f=0.28mm/r

    Thread Hole-making for Rake Face and Flank Face of Rotor Cavity

    Tool: 4111-M20*2.5

    Cutting data: V=100m/min   f=0.05mm/r

    Thread Hole Tapping for Flange Face of vent hole and inlet hole

    Tool: 4201-M16*2-6H

    Cutting data: V=30m/min  












    JOIN US

    Email
    Name
    Country
    不卡日本视频高清免费观看,大香伊蕉在人线免费视频,粉嫩的小仙女高潮喷水